Incremental Encoder#

The incremental encoder IP-Core (IncreEncoder_V26) evaluates signals of an incremental encoder and is compatible to Digital Encoder 1v00. It features multiple possibilities to calculate the rotor position and the rotational speed of the encoder.

Position: Calculates the rotational position of the encoder based on counting rising and falling edges on the A and B-lane of the encoder. Resets to zero based on the I-lane (once per mechanical revolution).
Position (electrical): Calculates the rotational position of the encoder and transforms the position to the electrical position of electric drive (e.g., permanent magnet synchronous machines). Uses the number of pole pairs to divide one mechanical turn of the encoder to (multiple) turns of the electrical system. Can only be used if the number of increments is an integer multiple of the number of pole pairs! The value of drive_pole_pair in the driver configuration has to be an integer multiple of the increments per turn or set to zero. If drive_pole_pair is an integer multiple of increments per turn, the electrical angle can be used and read by calling uz_incrementalEncoder_get_theta_el. If drive_pole_pair is set to 0, the function can not be called (assertion fires if it is called). If drive_pole_pair is not 0 and not an integer multiple of increments per turn, the initialization of the driver fails with an assertion. Note that the FPGA output port of the IP-Core outputs the (potentially false!) electrical position regardless of this setting!
Rotational speed: Calculates the rotational speed of the drive by counting the time between two consecutive rising edges of the A-lane in combination with an speed-dependent oversampling mechanism and subsequent filtering of the speed signal in the IP-Core. The oversampling mechanism allows to skip edges to improve the measurement at higher speeds.
Direction of rotation: Determines the direction of the rotation (clockwise / counterclockwise)

Hardware filter of rotational speed#

Subsystem omega_by_measure_time outputs \(\omega_{raw}\), new_measurement and oversampling factor \(k_{Oversample}\). The following calculation is done:

\[\omega_{scaled}=\frac{1}{\omega_{raw}} \cdot k_{Oversample}\]

This is fed to the Average_linear_Reg with the constants \(S_{factor}=6\) and \(S_{invFactor} = \frac{1}{6}\) (not used at all). Whenever new_measurement is true, the current value of \(\omega_{scaled}\) is added to an internal storage that sums up the rotational speed. After six (\(S_{factor}=6\)) measurements the internal storage is reset to zero, restarting the averaging. The value of the internal storage is divided by the number of samples that are currently in the internal storage and output.

IP-Core Hardware#

The IP-Core is generated using Matlab/Simulink HDL-Coder based on the model inc_enc_v26.slx (in ultrazohm_sw/ip-cores/IncreEncoder_V26_ip/Simulation/).

Vivado integration#

../../_images/increEncoder_vivado.png — Fig. 320 Vivado block design of incremental encoder IP-Core.#

Warning

The IP-Core (IPCORE_CLK) has to be sourced by a clock with \(100 MHz\)! For lower frequencies the accuracy of the encoder result is not tested.

Configuration registers (AXI)#

The following configuration registers are available for the IP-Core. The software driver writes to the registers based on the configuration that is provided to the initialization function.

PI2_Inc_AXI: Scales the output theta_el to \(0..2\pi\). Is calculated in the processor and written to the IP-Core. Calculation: \(\frac{2 \cdot \pi}{IncPerTurn \cdot QudratureFactor} \cdot PolePair\) with PolePair being the pole pairs of the drive.
Timer_FPGA_ms: Scales the timer, that is used to calculate the rotational speed, from FPGA clock ticks to seconds w.r.t. the number of increments and \(2\pi\). Default is \(\frac{IncPerTurn}{f_{IP-Core}} \cdot \frac{1}{2\pi}=7.958e-06\) with \(f_{IP-Core}=100 MHz\) and \(IncPerTurn=5000\).
IncPerTurn_mech: Configures the number of lines per mechanical revolution.
IncPerTurn_elec: Configures the number of lines per electrical revolution, i.e., w.r.t. to the pole pairs of a electrical machine. Set to IncPerTurn_mech divided by pole pairs of the electrical machine.
OverSamplingFactor: Calculation of the rotational speed omega is based on measuring the time between rising edges of the A-lane. If OverSampleFactor=1, every rising edge is used. For OverSampleFactor=n, every n-th rising ege is used. Based on the setting, the IP-Core adapts the OverSampleFactor over the operating range of the drive. The OverSamplingFactor is set by OmegaPerOverSampl_AXI4 in rad/s. Default value is \(500 \frac{1}{min} \cdot \frac{2\pi}{60 s}=52.3599 s^{-1}\).
PeriodEnd: Used to reset the counter that is used to calculate the rotational speed, which is output at countPerPeriod_AXI. Not recommended, use calculation based on time measurement based on counting edges of the A-lane instead (omega_AXI).
TimeoutValue: Used to set the timeout value in milliseconds for the omega_out port. If a timeout occurs, the omega_out port will be set to zero after the configured value has passed.
PositionOffset: Sets the mechanical offset for the \(\theta_{mech}\). \(\theta_{mech}\) can only be used in the PL.
ElectricalOffset: Sets the electrical offset for the \(\theta_{el}\). This changes the \(\theta_{el}\) in software and the PL.
CountingDirection: Sets the counting direction of the angle and rotation. Can be configured via an enum. Default is clock_wise.

Table Interfaces of the incremental encoder IP-Core lists all input and output ports (AXI and external port) that are present in the IP-Core.

Table 102 Interfaces of the incremental encoder IP-Core#
Port Name	Port Type	Data Type	Target Platform Interfaces	Function
A	Input	bool	External Signal	Lane A of encoder
B	Input	bool	External Signal	Lane B of encoder
I	Input	bool	External Signal	Lane I of encoder (zero)
PeriodEnd	Input	bool	External Signal	Resets subsystem that calculates `countPerPeriod_AXI4`
Theta_el	Output	sfix24_En20	External Signal	Theta electric based on the subsystem `Counter_theta_ele`
omega	Output	sfix24_En11	External Signal	Rotational speed based on time measurement between rising edge of A-lane (subsystem `omega_by_measure_time`)
position	Output	uint16_t	External Signal	Outputs the position of the encoder with a range of 0 to increments
count	Output	bool	External Signal	1 if edge counter is triggered - 0 otherwise
edge_rsvd	Output	bool	External Signal	1 if an edge is detected - 0 otherwise
OverSamplFactor	Output	uint16_t	External Signal	Reads back the over sample factor of the speed calculation
omega_MA_N4	Output	sfix24_En11	External Signal	omega but with an moving average over the last 4 measurements
timeout_active	Output	bool	External Signal	Active if a timeout occured
omegaA	Output	sfix24_En11	External Signal	omega calculated using only positiv edges of the A Line
omegaB	Output	sfix24_En11	External Signal	omega calculated using only positiv edges of the B Line
omegaNOTA	Output	sfix24_En11	External Signal	omega calculated using only negativ edges of the A Line
omegaNOTB	Output	sfix24_En11	External Signal	omega calculated using only negativ edges of the B Line
new_measurement	Output	bool	External Signal	indicates that an omega measurement of a Line has been completed
position_wOffset	Output	uint16_t	External Signal	Outputs the position shifted by `Position_offset_AXI4` of the encoder with a range of 0 to increments
Index_found	Output	bool	External Signal	Indicates whether the I-lane of the encoder has been found
Reset	Input	bool	AXI	Resets the IP-Core
Enable	Input	bool	AXI	Enables the IP-Core
Timestamp	Output	uint32_t	AXI	Returns unique IP timestamp
omega_AXI4	Output	sfix24_En11	AXI	same signal as omega
omega_MA_N4_AXI4	Output	sfix24_En11	AXI	omega but with an moving average over the last 4 measurements
theta_el_AXI4	Output	sfix24_en20	AXI	same signal as Theta_el
position_AXI4	Output	uint16_t	AXI	Outputs the position of the encoder with a range of 0 to increments
direction_AXI4	Output	sfix4	AXI	1 if rotation is clockwise - 0 otherwise
counterPerPeriod_AXI4	Output	int16	AXI	Result of `omega_by_count_lines` subsystem
PI2_Inc_AXI	Input	ufix24_En24	AXI	Scales the output of `theta_el` to 0 to \(2\pi\)
Timer_FPGA_ms_AXI4	Input	ufix32_En32	AXI	Scales clock ticks to rad/s
IncPerTurn_mech_AXI4	Input	uint16_t	AXI	Number of increments of the encoder of one mechanical turn
IncPerTurn_elek_AXI4	Input	uint16_t	AXI	Number of increments of the encoder divided by pole pairs for electrical angle
OmegaPerOverSampl_AXI4	Input	sfix24_En11	AXI	Oversampling factor for speed measurement - provided as multiple
Position_offset_AXI4	Input	uint16_t	AXI	Offset for theta_mech in increments
Theta_el_offset_AXI4	Input	uint16_t	AXI	Offset for theta_el in increments
Timeout_value_AXI4	Input	uint16_t	AXI	If a timeout occurs the omega_AXI4 port will be set to 0 after the specified time
CW_CCW_Switch_AXI4	Input	bool	AXI	Sets a clock_wise or counter_clock_wise counting direction
Position_wOffset_AXI4	Output	uint16_t	AXI	Outputs the position shifted by `Position_offset_AXI4` of the encoder with a range of 0 to increments
Index_found_AXI4	Output	bool	AXI	Indicates whether the I-lane of the encoder has been found

Software driver#

The software driver for the IP-Core handles the configuration of the aforementioned registers.

Listing 183 Initialization of an encoder#

struct uz_incrementalEncoder_config encoder_D5_config={
              .base_address=XPAR_UZ_DIGITAL_ADAPTER_D5_ADAPTER_INCREMENTAL_ENCODER_0_BASEADDR,
              .ip_core_frequency_Hz=100000000U,
              .line_number_per_turn_mech=5000U,
              .OmegaPerOverSample_in_rpm=500.0f,
              .drive_pole_pair=4U,
              .Encoder_elec_Offset = 0U,
              .counting_direction = clock_wise,
              .Speed_Timeout_ms = 10U //10ms
};
uz_incrementalEncoder_t* test_instance=uz_incrementalEncoder_init(testconfig);

Listing 184 Read position and speed#

float omega=uz_incrementalEncoder_get_omega_mech(test_instance);
float theta_el=uz_incrementalEncoder_get_theta_el(test_instance);
uint32_t position=uz_incrementalEncoder_get_position(test_instance);

Driver reference#

typedef struct uz_incrementalEncoder_t uz_incrementalEncoder_t#: Object data type definition of the incremental encoder IP-Core driver.

enum uz_incrementalEncoder_counting_direction#

enum for readable configuring counting direction of the IP Core.

Values:

enumerator uz_incrementalEncoder_counting_clock_wise#

enumerator uz_incrementalEncoder_counting_counter_clock_wise#

struct uz_incrementalEncoder_config#

Configuration struct for the encoder driver.

Public Members

uint32_t base_address#: Base address of IP-Core instance

uint32_t ip_core_frequency_Hz#: Clock frequency of IP-Core

uint32_t line_number_per_turn_mech#: Number of lines eper one mechanical turn of the attached encoder

float OmegaPerOverSample_in_rpm#: Rotational speed omega in 1/min after which the OverSamplingFactor is increased by one

uint32_t drive_pole_pair#: Number of pole pairs of the electric drive that is attached to the encoder. Set to zero if no drive is attached or increments per mechanical turn is not an integer multiple of pole pairs

uint32_t Encoder_mech_Offset#: Set the Mechanical Encoder Offset in increments

uint32_t Encoder_elec_Offset#: Set the electrical Encoder Offset in increments

enum uz_incrementalEncoder_counting_direction counting_direction#

Set the counting direction to

0=clock_wise or

1=counter_clock_wise

uint32_t Speed_Timeout_ms#: Milliseconds after the omega_out jumps to zero if a timeout occurs

uz_incrementalEncoder_t *uz_incrementalEncoder_init(struct uz_incrementalEncoder_config config)#

Initialization of one instance of the driver for the incremental encoder IP-Core.

Parameters:

config – Configuration values for the IP-Core

Returns:

uz_incrementalEncoder_t* Pointer to initialized instance

float uz_incrementalEncoder_get_omega_mech(uz_incrementalEncoder_t *self)#

Returns the measured omega based on counting edges of the A-lane in 1/s.

Parameters:

self – Pointer to the instance

Returns:

float omega_mech

float uz_incrementalEncoder_get_theta_el(uz_incrementalEncoder_t *self)#

Returns the measured electrical angle in 0..2pi range if drive_pole_pair is not zero in the config.

Parameters:

self – Pointer to the instance

Returns:

float theta_el

uint32_t uz_incrementalEncoder_get_position(uz_incrementalEncoder_t *self)#

Returns the measured mechanical angle in 0..increments.

Parameters:

self – Pointer to the instance

Returns:

uint32_t position

Incremental Encoder#

Hardware filter of rotational speed#

IP-Core Hardware#

Vivado integration#

Configuration registers (AXI)#

Software driver#

Driver reference#

This Page